Skip to content
Get a Quote
Insight

Two air-system protections inspectors check before anything else

A coal mine in Shanxi was fined RMB 90,000 after an inspection found, among other things, that its shaft air compressor was oil-lubricated with no oil-cutoff protection fitted, and that the air receiver had no over-temperature protection. The fine was issued under Article 99(2) of the Work Safety Law.

Both findings concern devices that cost very little and are routinely bypassed. They are worth understanding even outside mining, because the same two protections apply to any lubricated compressor feeding a pressure vessel.

Oil-cutoff protection: what it does and why it exists

A lubricated screw compressor depends on an oil film between the rotors and between rotor and casing. If oil pressure or flow is lost while the machine keeps turning, metal contact follows quickly: the rotors score, clearances close, and in the worst case the machine seizes with a large amount of hot oil inside it.

Oil-cutoff protection is the interlock that stops the machine when oil pressure drops below a threshold, before damage progresses. Its purpose is not machine life. It is fire and explosion prevention: a seized lubricated machine can reach temperatures that ignite oil mist, and the discharge system downstream — receiver, piping, filters — is full of air that will carry it.

What an inspection checks:

  • The interlock exists and is wired to trip the machine, not simply to raise an alarm on a display.
  • It has been function-tested, with a record. A pressure switch that has never been tripped is an assumption.
  • It has not been bypassed, which is the usual finding: a nuisance trip gets jumpered to keep production running, and the jumper outlives the shift that fitted it.
  • The trip threshold is set against the machine’s actual oil pressure, not left at a factory default that no longer matches the installation.

Receiver over-temperature protection: the less obvious one

Discharge air leaving a lubricated compressor is hot, and it arrives at the receiver with the oil that passed the separator. Sustained high temperature does two things: it degrades the oil, producing varnish and carbon, and it pushes the oil/air mixture closer to its ignition range. Carbon deposits on discharge valves and pipework are the classic ignition source in compressor fires.

Over-temperature protection on the receiver is a temperature switch or transmitter that alarms or trips at a set point, so that a cooling failure, a fouled cooler or a stuck thermostatic valve is caught before the oil is cooked.

What to check:

  • A sensor actually installed on the vessel, not a reading taken off the compressor controller’s discharge temperature.
  • Set point below the oil’s degradation threshold, with a margin for summer ambient.
  • Automatic trip or alarm routed to someone, not a value displayed in an unmanned room.
  • The vessel’s own statutory items intact: relief valve in date, drain working, inspection certificate current. Over-temperature protection does not replace any of them.

Why these two, together

The two failures are the same failure in different places: a protection that depends on a device nobody tests. Both are cheap to install, both are cheap to bypass, and both are invisible until an inspector or a fire finds them.

A workable routine for any plant with lubricated compressors:

  1. List every protection on every machine and vessel, with what it protects against and how it trips.
  2. Function-test each one annually and record the result, in the same way a relief valve is tested — including the ones that are inconvenient to trip.
  3. Control bypasses formally. A jumper fitted to clear a nuisance trip should require an entry, an owner and a removal date.
  4. Check the set points against operating reality after any change of cooler, oil grade or summer ambient.

The wider point

Compressed air systems are usually inspected for efficiency: leaks, pressure, specific power. Safety findings like these tend to come from a different inspection, on a different day, with a different consequence. Treating the two lists as one — machine protection, vessel protection, then efficiency — is cheaper than discovering the first list through a fine.

The RMB 90,000 penalty in this case was one line in a longer list of findings that also included lifting equipment put into service without testing. The pattern is familiar: the equipment that works is the equipment nobody re-examines.

—

Industry practice note. Facts as reported in the enforcement notice; the site described is not a SIND project.

Planning a compressed-air upgrade? Talk to SIND’s engineers.

Facts as reported by industry press; the project described is not a SIND project.

Planning a compressed air project?

Talk to an engineer
SIND Applications Engineering

The SIND applications engineering team reviews compressed air duty points, sizes systems and writes the technical articles published on this site.

Published November 16, 2026.

SIND
Jafor Nayan Sales Engineer Biruk Argaw Sales Engineer