Classifying compressed air in a food plant: three categories, three specifications
Food plants tend to specify compressed air in two states: “oil-free, because it’s food” or “whatever the last compressor was”. Neither is a specification. The industry convention is to split use points into three categories first, then write the air quality requirement for each — because the cost of over-specifying every point is paid, permanently, in electricity and filter pressure drop.
The three categories
1. Contact air — directly touches the food.
Used in mixing, blowing off product, and in processes where the air stream meets the product or its primary package. This is the strictest category: the air must be oil-free, with controlled dust content and pressure dew point, and it should be treated as a food-contact utility in the plant’s own hazard analysis.
2. Non-contact, high-risk.
Air used in the production environment but not touching product — packaging areas are the usual example. These points are governed by the relevant food safety standards rather than by a single oil content figure, and the practical requirement is that the air must not contaminate product or packaging surfaces, directly or by settling.
3. Non-contact, low-risk.
Air that reaches neither the product nor a food-contact surface: pneumatic tools, control valves, air motors, actuators. Purity requirements here are much lower — typically dry enough not to corrode instruments and free of liquid water and particulate. This is where plants overspend most often.
Why the classification pays
Three requirements applied to every point forces the whole system to the strictest one. The consequence is a station that dries air to a very low dew point and filters it to a very fine level, then delivers that air to cylinder actuators — paying for both the drying energy and the filter pressure drop across the entire flow.
Classifying first allows a plant to choose between two architectures:
- One high-quality system for contact and high-risk points, a second, simpler system for instruments and actuators. Two smaller compressors and two headers, one of them lightly treated.
- One system at contact quality, with local treatment only where needed. Simpler to operate, but every cubic metre pays for the strictest requirement.
Which one is cheaper depends on the ratio of contact air to total air. Plants where contact air is a small fraction usually win with two systems; plants where it is most of the flow usually win with one.
The other three requirements food plants share
Classification settles the air quality. Three other requirements apply across the plant whatever the category:
Continuous supply. Food lines do not tolerate air interruptions — a stop mid-process is a hygiene event, not just a production event. That means explicit standby capacity and a station that can lose a machine without losing pressure.
Turndown. Food plants run campaigns: a line may consume at full rate for one shift and a fraction of it for the next. Variable-speed machines and a sequenced station matter more here than the difference between two compressor models.
Cleanable systems. Dryers, filters and drains collect condensate. In a food environment the drainage path matters as much as the air quality — a receiver drained manually once a shift is a microbial risk sitting next to a production hall.
Specifying in practice
Work through the plant point by point and write down four values for each: required pressure, flow, dew point and allowable oil carryover. Then group them. What usually emerges is:
- A small number of contact points requiring the full treatment.
- A larger number of actuator and instrument points that need nothing more than dry, filtered air.
- A middle group in packaging that needs careful thought, because it is the category most often mis-specified in both directions.
Two checks before ordering equipment:
- Is the oil-free requirement at the compressor, or at the point of use? A lubricated machine with full filtration is not the same as an oil-free machine, and the choice depends on how much contact air the plant actually has and what the hazard analysis concludes.
- Is the dryer sized at peak flow, with a dew point margin below the coldest surface in the system? Refrigerated dryers lose dew point performance as inlet temperature rises; a dryer specified on average load will not hold its figure in summer.
The point of the exercise
Every food plant has these three categories whether or not it has written them down. Writing them down turns a vague requirement into an equipment list, a piping layout and an operating routine — and it is the only way to answer the question that comes later: why is this plant drying twice as much air as it uses?
—
Industry practice note. Application guidance as reported by industry press; the plant described is not a SIND project.
Planning a compressed-air upgrade? Talk to SIND’s engineers.
Facts as reported by industry press; the project described is not a SIND project.
Planning a compressed air project?
Talk to an engineerPublished November 16, 2026.