Design Cooling, Aftercoolers, and Heat Recovery as One System
When a compressed-air plant is designed, cooling is often decided as a utility question — air-cooled or water-cooled, roof or tower, indoor or outdoor — while heat recovery is discussed later as an energy-saving option, and the dryer is selected from a capacity table. Those decisions leak into one another. The temperature leaving the aftercooler is the temperature entering the dryer. The water or air that carries heat away from the compressor is also the stream that might be reused. If those facts are ignored, a plant can buy a correctly “sized” dryer that is under-capacity in real weather, or a heat-recovery idea that has no useful load.
This article is a design briefing, not a product selection guide and not a report on a SIND installation. Temperature figures below are common design values as described in the cited sources. They are not universal limits and not SIND ratings.
Start with the cooling medium, not with the heat-recovery sketch
Hank Van Ormer’s 2023 two-part series in Compressed Air Best Practices is useful because it starts with cooling as an operating cost and a machine-protection issue, then turns to heat recovery. Air-cooled and water-cooled packages each have a place. The choice depends on ambient temperature and cleanliness, whether the load is continuous, whether cooling water is already available and at what cost, and how the rejected heat might be used. Historical practice — larger machines often being water-cooled — is not by itself a sufficient reason to repeat the same choice on a new site.
Whoever sizes the compressor should also say how the heat will be rejected, at what temperatures, and what that means for the room, the cooling system, and the dryer. A later “we can add a heat-recovery option” conversation is weaker if the cooling circuit has already been drawn in a way that makes recovery difficult, or if the only available heat sink is seasonal.
A 2023 article by Clayton Penhallegon, Jr., P.E., on tankless central cooling systems is related background rather than a requirement for every compressor room. It is a reminder that a central cooling loop has its own design conventions, including whether an open tank is actually needed. Those conventions should be reviewed with the cooling engineer; they are not a standard package feature.
The aftercooler sets the dryer up to succeed or to fail
Part 2 of Van Ormer’s series is the hinge between cooling and air treatment. After the compressor, an aftercooler and drain do most of the work of knocking out water before the dryer ever sees the air. If cooling water is warmer than the aftercooler was designed for, or if flow is short, the approach temperature rises and the air arrives at the dryer hotter and wetter than the dryer data sheet assumed.
Van Ormer describes typical design conditions that appear often in North American practice: many compressors are discussed as being designed around a cooling-water maximum inlet of about 100 °F (38 °C), with some applications up to about 110 °F (43 °C); discharge water is often in a 120–130 °F (49–54 °C) range; and many dryers in the U.S. market are rated at a stated inlet condition, commonly 100 psig (7 bar) and 100 °F (38 °C). Those figures are the author’s account of common design values, opened and checked on the original page. They are not a guarantee for every machine. The design lesson still holds outside that market: if inlet temperature to the dryer rises, moisture load rises and the dryer’s real capacity falls, even though the nameplate flow has not changed.
That is why “the dryer is undersized” is sometimes a cooling problem. It is also why overcooling is not automatically clever. Driving the air or the cooling water to an unnecessarily low temperature can waste utilities, complicate heat recovery, and, in some systems, create condensation in the wrong place. The target is a stable, specified approach — not the lowest temperature the tower can reach on a cold day.
Heat recovery is the same heat, put to work
If the compressor is already rejecting a large fraction of its input energy as heat, recovery is not a separate physical process. It is a decision about where that heat is allowed to go. Ron Marshall’s July 2024 retrospective in Plant Services notes that heat-recovery provisions have become easier to integrate than they were a decade earlier. That observation is not a SIND performance claim, and this article does not attach a recovery percentage or a payback to any SIND system.
Marshall’s December 2023 interview adds the condition that actually decides whether a project is worth doing: the heat has to go to a load that exists for enough of the year. A winter-only space-heating use, or a process that is already idle when the compressors are busiest, will not support the same case as a year-round water or process load. Cooling-system design should therefore record the available temperature and the coincidental load before anyone treats heat recovery as a standard energy-saving line item.
A practical checklist
A project team can reasonably write down, in one place:
- How each compressor is cooled, and at what design ambient or water temperatures.
- The intended aftercooler outlet temperature, and the dryer’s rated inlet conditions.
- What happens to dryer capacity if summer cooling conditions are worse than the rating point.
- Whether any heat-recovery use is coincident with compressor operation, and at what temperature.
- Who owns the central cooling loop, if there is one, and whether that loop’s assumptions — tanks, setpoints, winterization — have been checked.
Related reading on this site
Live SIND articles already make the case for waste-heat recovery and outline engineering practice. This article is the cooling-and-aftercooler companion; it does not replace The Case for Waste-Heat Recovery in Compressed Air Systems, Waste-Heat Recovery: Key Points and Advantages, or Waste-Heat Recovery Technology and Engineering Practice. See also Choosing Dryers and Filters for Compressed Air.
Planning cooling, treatment, or heat recovery on a compressed-air system? Talk to a SIND engineer · Browse product families.
Sources (publication dates are the source articles’ own dates, verified on the original pages; they are not the publication date of this SIND article). Temperature figures are the cited authors’ accounts of common design values, not SIND ratings. Summarised by SIND editorial; no SIND case, recovery percentage, or certification is claimed.
- Hank Van Ormer, APenergy, “Evaluating Air Compressor Cooling and Heat Recovery Part 1,” Compressed Air Best Practices, 3 July 2023. airbestpractices.com
- Hank Van Ormer, APenergy, “Evaluating Air Compressor Cooling and Heat Recovery Part 2 – Centralized Systems,” Compressed Air Best Practices, 29 August 2023. airbestpractices.com
- Clayton Penhallegon, Jr., P.E., Integrated Services Group, “Tank Applications in Central Cooling Systems – Tankless Systems,” Compressed Air Best Practices, visible byline 31 March 2023 (schema datePublished 14 March 2023). Related background only. airbestpractices.com
- Ron Marshall, “Compressed air innovations in industry: A 10-year retrospective,” Plant Services, 22 July 2024. plantservices.com
- Thomas Wilk, interview with Ron Marshall, “The true cost of common compressed air problems,” Plant Services, 19 December 2023. plantservices.com
Planning a compressed air project?
Talk to an engineerPublished November 12, 2026.