Measure the Dew Point You Are Paying For
Compressed-air specifications almost always name a dew point. In daily operation, that number is often treated as a property of the dryer that was purchased, rather than as a condition that has to be measured. If dew point is not measured at the right place, with a sensor that actually covers the range you care about, a plant can spend energy over-drying the air — or discover wet air only after a quality problem appears.
This article is about measurement and dryer-performance checks. It is not a buying guide that compares refrigerated and desiccant dryers, and it does not restate SIND’s existing articles on dryer type selection or the cost of clean, dry air. The figures cited below come from the sources listed at the end. They are not SIND dryer or instrument ratings, and they are not results from a SIND installation.
Dew point is a system result, not a nameplate
Dew point describes how far the air can be cooled before water vapor starts to condense. In a compressed-air system it is one of the practical measures of whether the treatment train is doing its job. A 2023 technical article by Antti Viitanen (Vaisala) in Compressed Air Best Practices argues that an inaccurate or poorly placed measurement can push a plant in either of two expensive directions: drying more than the process needs, or allowing moisture that later condenses in pipes, tools, or product. The useful question is not only “what dew point did we buy?” but “what dew point is being delivered, and where?”
That distinction matters because pressure, temperature, and location all change the reading. A value taken at the dryer outlet is not automatically the same as the condition at a distant point of use, especially if pipework is uninsulated, drains are unreliable, or air sits in an oversized network. A specification written at one pressure also has to be interpreted at the pressure where the air is actually used.
Measure at the dryer — and, when the process is critical, further downstream
A dryer-outlet measurement answers a maintenance question: is this machine still producing the dryness it is supposed to produce? Viitanen’s discussion of measurement practice, and Ron Marshall’s December 2023 interview in Plant Services, both come back to the same habit: do not assume the dryer is working because it is powered and the panel looks normal. A dew-point instrument at the outlet is one of the few ways to see a failed drain, a fouled heat exchanger, a saturated desiccant bed, or a control fault before the problem shows up as water in a drop leg.
A second measurement, closer to a sensitive process, answers a different question: is the distribution system preserving that dryness? If the two readings diverge, the problem may be in the pipework, not in the dryer. That is a more precise diagnosis than “the air quality is poor,” and it avoids replacing treatment equipment when a leak, drain, or pipe condition is the real issue.
None of this requires a plant to instrument every drop. It does argue against relying on a commissioning reading taken once, or on the dryer’s original data sheet, as a substitute for current evidence.
Match the sensor to the dryer — then use the signal
Dryer types produce very different dew-point ranges. In a June 2024 Compressed Air Best Practices article, Simon Gleissner (SUTO iTEC) describes refrigerated dryers as typically operating around a pressure dew point of about +3 °C (+37.4 °F), and desiccant dryers as capable of much lower dew points — the article discusses a range from about −60 °C to −100 °C (−76 °F to −148 °F), depending on the design. Those figures are the author’s industry descriptions. They are not SIND catalog ratings and should not be copied onto a quotation as if they were.
The practical consequence is that a sensor chosen for a refrigerated dryer may be a poor fit for a desiccant dryer, and the reverse is also true. Range, accuracy around the control point, and the way the instrument behaves when the air is wetter than expected all affect whether an alarm is useful or merely noisy.
Gleissner also emphasizes integration: a dew-point transmitter that can be read by the plant control or monitoring system is more valuable than a local display that nobody trends. On a desiccant dryer, a reliable dew-point signal can support purge or cycle control, so the machine does not regenerate on a fixed timer when the bed is still dry. That is an energy issue as much as a quality issue. Over-purging is one of the quieter ways a high-specification treatment plant becomes expensive.
Any such control change should follow the dryer manufacturer’s guidance. This article is not a control-settings procedure, and it does not recommend a sensor brand.
Treat vendor figures as starting points, not plant facts
Two of the sources behind this article were written by instrument manufacturers. That does not make the measurement argument invalid, but it does mean that “typical” ranges and any savings comments in those articles should stay attached to those articles. They are not SIND results, and they are not a promise that adding a sensor will cut a stated share of dryer energy.
Marshall’s 2023 interview is useful for a different reason: it treats dryer performance as something to be verified in service, alongside leaks and pressure, rather than as a one-time design choice. His July 2024 retrospective also notes the wider availability of better instruments and monitoring. The conservative point for plant teams is simple: measurement makes dryer performance visible. It does not, by itself, select the dryer type.
Related reading on this site
This article sits beside, and does not replace, Refrigerated vs Desiccant Air Dryer, Choosing Dryers and Filters for Compressed Air, and What Clean, Dry Compressed Air Really Costs.
Need a dew-point or dryer-performance check on a system design? Talk to a SIND engineer · Browse product families.
Sources (publication dates are the source articles’ own dates, verified on the original pages; they are not the publication date of this SIND article). Summarised by SIND editorial; no SIND case, rating, or certification is claimed.
- Antti Viitanen, Vaisala, “A Deep Dive into Dew Point Measurement in Compressed Air Systems,” Compressed Air Best Practices, 30 May 2023. airbestpractices.com
- Simon Gleissner, SUTO iTEC, “Selecting the Optimal Dew Point Sensor for Compressed Air Dryers,” Compressed Air Best Practices, visible byline 27 June 2024 (schema datePublished 28 June 2024). airbestpractices.com
- Thomas Wilk, interview with Ron Marshall, “The true cost of common compressed air problems,” Plant Services, 19 December 2023. plantservices.com
- Ron Marshall, “Compressed air innovations in industry: A 10-year retrospective,” Plant Services, 22 July 2024. plantservices.com
Planning a compressed air project?
Talk to an engineerPublished November 12, 2026.